Page 1 - In the left column under Finished Measurements, the sample size shown should be "34 ½" / 87.5 cm".

Page 2 - In the left sidebar under "Shadow Wrap, worked knitwise (swk)", at the end of the first line the word "stitch" was misspelled.

Page 2 - In the left sidebar, directly above "Shadow Wrap, worked knitwise (swk)" and below "Rep Rows 1-4 for pattern", a new paragraph has been inserted:

Working Shadow Wraps: When working the Shadow Wraps either knitwise or purlwise, the doubled stitch is on the left hand needle after the worked is turned. This doubled stitch will be slipped at the beginning of the following row.

Page 3 - Under "Increasing short row wedge", the end of the set up row (after the turn) should read, "Sl 1, p2 (2, 2, 3, 3, 3, 3), swp, turn.

Page 1 - A note has been added about yarn over short rows.

Page 2 - Additional instructions have been added on how to work certain stitches on the wrong side.

Pages 2 and 5 - All instances of the symbol "w&t" have been replaced by "yarn over tightly".

Page 3 - Under Sleeves in the second column, the last sentence of the third paragraph should read: "You have knit a turning ridge, joined the sleeve pieces together, and worked Row 1 of the Lace Chart."

Page 4 - In the chart key, the defintion for the 4th symbol (twisted stitch with a filled-in loop) should read: "WS: purl through back loop".

Page 4 - On the chart, some decreases have been moved:

On rows 14 and 21, the k2tog symbols have been removed; all stitches are knit.

On row 15, there is a k2tog at the second stitch and the last stitch (both stitches are CC). On row 22, there is a k2tog at the first stitch (CC) and the second to the last st (MC).

Pdf was optimized for faster viewing.

Page 3 - Two 5-st cable symbols have been added to the chart key. These symbols are used only on the Underarm Chart on page 5.

Page 5 - The first and last cable symbols on rows 2, 4, 6, 8, and 10 have been updated with the new 5-st cable symbols.

It should be noted that this is a chart update only. Halliard can be knit as is using previous pdf versions.

Page 1 - Under Crescent in the right column, a marker has been added to row 1. It now reads:

Row 1 (RS): K6, yo, cdd, yo, k6, [pm, k7, yo, cdd, yo, k6] 3 times, pm, k7, yo, cdd, yo, k7, [pm, k6, yo, cdd, yo, k7] 3 times, pm, end k6, yo, cdd, yo, k6.

Page 4 - On row 29 of the chart, the note now reads "Change to size 9 US / 5.5 mm needle."

Page 2 - In the left column under Setup of Garter Stitch Grafting, Step 4 should read: "Bring yarn purlwise through next stitch
on front needle, leaving the stitch in place." 3, p1, k1, left lifted increase...." At the end, the last the last 6 stitches should be: "....right lifted increase, k1, p1, k3."

Page 2 - In the right column just before Begin Slipped Rib pattern and right after "...WS facing for next row", there should be a line that reads: "Change to larger needles."

Page 2: In the right column, the fifth paragraph should begin with: Next row (RS): K1, k2tog, k1, Rlinc, knit to last 4 sts, Llinc, k1, ssk, k1."

Page 3 - In Abbreviations, the definition for C3F has changed to: "Slip 1 stitch to cable needle and hold to front, knit 2 stitches, then knit 1 stitch on the cable needle".

Page 1 - In the left column under "Waistband Pattern (Panel of 19 sts)", Row 2 now begins with "Sl 1 wyib, [p1, p1 wyif...."

Page 1 - In the left column under "Waistband Pattern (Panel of 19 sts)", Row 2 now begins with "Sl 1 wyif, [p1, sl 1 wyib...."

Page 4 - The sleeve chart has been redrawn to include 3 edge stitches and to realign the pattern for all 9 sizes.

Page 2 - On the schematic, the sleeve letters have changed:

P: Sleeve Cap depth
(Originally "Q" on schematic and "O" in measurements.)

Q: Sleeve length
(Originally "R" on schematic and "P" in measurements.)

R: Upper Arm width
(Originally "S" on schematic and "Q" in measurements.)

S: Cuff width
(Originally "T" on schematic and "R" in measurements.)

Page 3 - Under Right Front, the sentence begins, "With smaller needles..."

Page 5 - In the Chart key, the definition for the last symbol in the right column should be "Sl 1 st to cable needle and hold to front, k2, k1 from cable needle"